How To Install Drive Toilet Seat Riser

Installing a new toilet seat is an easy DIY project. Whether you lot're replacing yours because it's old, or because you merely want a new fashion, all you need are some bones tools and a few minutes. Unbolt the one-time seat, then pop the new ane in place using the hardware included in your new toilet seat'south box. The only trouble yous're likely to see is if the one-time bolts are stuck, but a little elbow grease tin take care of that trouble.

1

Measure out your electric current toilet bowl before buying a new seat. Nearly toilets are standard sized, and whatever replacement seat should fit. If you want to exist extra sure, accept a tape measure to bank check the distance between the bolt holes in the toilet bowl. Then make sure the distance between the bolts on the replacement seat is the same.
2
Choose the mode of seat you want. Toilet seats come up in two basic styles, and a home supply store should accept several brands to choose from. The standard variety is rounded, but you can choose an elongated one if you prefer. You can besides buy a "whisper close" seat that has special pads on the bottom to prevent it from slamming downwards on the bowl.^[one]
- Toilet seats come in a range of prices. You lot should be able to notice the cheapest for $20-30, but others that cost twice as much or more.
3

Cull a seat color that matches your current toilet bowl. You lot can find toilet seats in a variety of colors. Choose 1 that matches the toilet bowl (normally white) for a classic await, or cull a contrasting colour to make a bolder statement. For instance, y'all could choose a bluish or wooden toilet seat to contrast with a white bowl.
four
Gather your tools for the projection. You'll demand just a few simple ones to handle this projection. If you lot don't already have these at abode, caput down to the hardware store and become:^[2]
- An adjustable wrench or pliers
- A flathead screwdriver
- Spray oil such as WD-40 (optional)
- A small hacksaw (optional)

1
Pop off the commodities caps, if necessary. Look at the edge of the one-time toilet seat, nigh the tank. You may run across plastic caps where the seat's hinges attach to the toilet basin, i on each side. If so, gently slide the flathead screwdriver under their edge and pry them off.^[three]
- If there are no bolt caps, yous volition just encounter the bolts themselves attaching the hinges of the seat to the toilet bowl.
2

Loosen the nuts. Hold your adaptable wrench and await underneath the edge of sides of the toilet bowl. You should see bolts going down through the porcelain, held in place by nuts. In that location will exist one on each side of the bowl. Attach the adjustable wrench to each nut. Turn the wrench counterclockwise to loosen the nuts.^[four]
three
Remove the former seat's bolts. The bolts at the base of the hinges on top of the toilet bowl may be slotted for a screwdriver. If and so, use yours and turn each bolt counterclockwise until it comes out. Otherwise, yous can continue turning the nuts counterclockwise until they come off.
- If your old seat has washers between the nut and bowl, remove those too.
4
Wrestle with the old bolts, if they're stuck. On some older toilets, the bolts might be rusted or stuck in identify by grime. If so, they may non come out hands. Don't panic -- you accept some options! Get-go, spray WD-40 on the threads of the rusted bolts. Let it sit down for ten minutes, then endeavour once more to remove the bolts.^[5]
- If that doesn't work, place your adaptable wrench on the nut. Hold it in place as you use the screwdriver in your other hand and attempt to turn the bolt out.
- If the bolts are yet stuck, use your small hacksaw to saw them off. Identify the bract just under the toilet bowl, at the peak of the nut, and gently saw dorsum and forth until you cut the bolt all the way off.
5

Dispose of the old seat and hardware. Lift the bolts out of the basin, if y'all haven't already. You lot should then exist able to remove the toilet seat and its hinges easily. Toss out the old seat, bolts, and nuts.^{[half dozen]}

i
Set the new seat in place. Remove information technology from the box. The hinges on the seat will be pre-fastened. Place these exactly where the hinges on the quondam seat were located.^[7]
- The box will likewise contain bolts and nuts. It may likewise include plastic caps to go over the bolts. Set this hardware to the side.
2
Drop the bolts into identify. Take a bolt in your mitt. The hinges will have holes for the bolts to be inserted into. Since the toilet seat is in place exactly where the previous seat was, these holes will also be positioned direct on top of the holes in the summit of the toilet bowl. Drop the bolts through the holes in the hinges and basin, with the caput of the bolt on tiptop.^[viii]
- Don't worry. Since the bolts have a caput, they won't autumn all the way through the holes.
3
Thread the nuts onto the bolts. Pick up ane of the nuts. Await at 1 side of the toilet bowl. You should now run into the end of ane of the bolts sticking downward through the summit of the bowl. Turn the nut onto the commodities (clockwise) until it is equally tight equally you can go it by hand. Utilise your adaptable wrench to tighten the nut just a bit further.^[9]
- Repeat with the other nut on the other side of the toilet.
- If your hardware includes washers as well, place these on the bolts threads, then put on the nut.
- If the hinges have plastic caps attached (or if these are included in the box with the new toilet seat), snap these in place by pushing them down on the heads of the bolts in one case you lot're done.
4
Snap the seat into identify, alternatively. For some models of toilet seats, you don't bulldoze the bolts through the hinges. Instead, yous driblet the bolts direct to the holes on either side of the toilet bowl, instead of driving them through the hinges beginning. So set them in identify with basics. The seat'south hinges will snap onto or slide over the bolt heads.^[10]
- Double-bank check the instructions that came with your toilet seat if yous have this multifariousness.

Add New Question

Question

How do I fit a new toilet seat if there is no access beneath to tighten the screws?

Use summit fixing fittings. These are common now and are used when you cannot access the fittings to tighten from underneath.
Question

How do I remove the onetime seat?

Pop up two white tabs. Use a screwdriver to remove the two screws. Lift up the erstwhile seat.
Question

How can I get the seat even?

A level is the best tool to brand sure the seat is perfectly level before installing it.
Question

What should I do if the hinge caps won't push down as it says in the instructions?

Attempt to push information technology difficult, or use a cloth over the hinge caps and a hammer to gently secure the caps.
Question

What if the two white tabs are so former that they won't pop up even when prying with a flathead screwdriver?

If you're tossing the whole thing anyway, break them. If y'all crack them, y'all tin can wedge the screwdriver in there to get information technology the balance of the way off.
Question

How can I tighten a toilet seat with clip zipper?

Toilet seats are fickle little things. Sometimes, y'all just can't get them to go in *just* the right spot.
Question

What do I practice if the bolts on my toilet seat keep loosening?

Use Loctite Lock 'due north Seal, which is an fantabulous fast acting bolt thread sealer. Information technology can be loosened with normal tools. It is possible to utilize on plastic bolts just will probable compromise the integrity of the plumbing fixtures (the chemicals in Loctite may damage the plastic).
Question

What should I do if the bolts are then tight I can't get them off?

Endeavour WD-40 and leave for xxx minutes or and so before having another get. You may be able to loosen the nuts on the bolt by trying to tighten them beginning by tapping on the spanner/wrench etc. Don't do it besides hard!
Question

What do I practice if I tin't tighten i of the bolts on my new toilet seat?

If it's a metal bolt, try Loctite Lock 'N Seal on the commodities thread, which should fill the thread ridges and provide grip for the nut. The nut can exist removed with ordinary tools. But use on the thread where grip is required, and don't spill or drip on the floor. (Probably best non to apply on plastic bolts, though.)

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Things You'll Need

Toilet seat
Flathead screwdriver
Wrench or adjustable pliers
Spray oil
Small-scale hacksaw

About this commodity

Article Summary X

If your toilet'south set for a new seat, start by measuring the distance between the ii bolts on the toilet bowl and so you know what size seat to get. Most toilet seats are the aforementioned size, just it'south better to check simply in case! One time you've bought a new seat that fits, apply a flathead screwdriver to pry off the caps on the bolts that adhere the one-time seat to the bowl. If at that place aren't any caps, you lot tin skip this step. Next, employ an adjustable wrench to loosen and remove the nut on each bolt so you tin elevator the former seat off. When the old seat is off, hold the new seat over the toilet bowl, and drop the bolts into the empty holes where the old bolts were. Cease by threading the nuts onto the bolts to tighten the new seat into place. For tips on how to loosen old bolts if they're stuck, scroll down!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 462,018 times.