How To Install Street Light

How to install solar street low-cal ? I recall most of people who start to enter this business organization would like to acquire. Now let us introduce the item procedure to install solar street light.

The Composition of Solar Street Light .
Solar street low-cal mainly is made up of solar panel, smart controller, bombardment, lighting source, lamp-post and bracket, etc. Solar street light is to adopt solar console converting solar ability into electrical power in daytime when solar panel is radiated by solar. When solar irradiance gradually decreases in night, smart controller can notice some value, it would control bombardment to discharge for LED lamp, then the LED lamp can car to work in dark. Smart controller can protect battery from over-accuse and over-discharge, and control the working time of LED lamp.

ane. The Foundation Casting.
1) Confirm the installation site.
Installation site should exist according to construction drawings and local geologic state of affairs, delight confirm no any shadow roofing the top of solar street lite, the interval between each 2 lights is nearly 40m.

two) Excavate the Foundation Ditch for Solar Street Light.
Delight excavate the foundation ditch in the confirming site, the foundation ditch should be deeper if the soil texture is soft among 1m area of the globe surface. At the same time, please confirm and protect excavation site and other facilities, such as cables, pipes, etc.

3) Please chip the foundation ditch to be battery box. Delight keep the foundation ditch has enough room to bury bombardment.

4) Casting the Foundation Embedded Part.
Delight put the embedded office into the foundation ditch, and put one finish of steel wire tube in the middle of embedded part, another i end put with the battery. Keep the embedded part, The foundation and state expanse should have the aforementioned horizontal plane. Then employ physical to bandage and fix the embedded part. Please continue to stir even during the casting, to guarantee the sealing and fastness for whole of embedded role.

5) Delight make clean the rest on the position plate in time after completing the construction, the solar street light tin can offset to exist installed afterward concrete being consummate solidification (Ordinarily information technology is nigh four days, quondam information technology is three days if whether is well).

2. The Installation of Solar Panel, Bracket, Lamp-Post, LED Lamp and Lamp-Post.
1) The installation of solar panel.
(ane) Please put solar panel on the brackets and utilize screws to set, to keep information technology fastness and reliability.

(ii) Connect the output cables of solar panel, delight notice to correctly connect their positive (+) and negative (-), and use ribbon to fasten the output cables of solar console.

(3) Please process tinning for the wiring terminal of solar panel, to protect wires from existence oxidized.

2) Installation for the LED Lamp.
(1) Please threading lamp wires out from lamp arm, outgoing some lamp wire to install lamp head.

(two) Support the lamp-postal service, threading another wiring last out from reserved pigsty of lamp-post, and install lamp head in another wiring terminal.

(iii) Use screw to gear up lamp-arm and lamp-post.

(4) Please marker one lamp-mail last, use pocket-sized conduit to thread the wires of solar panel and LED lamp to the bottom of lamp-postal service, and fix solar panel on the lamp-post. Please check if every screw has been fastened and waiting for crane to lift the lamp-mail.

3) Lift the Lamp-post.
(1) The fastness situation of every components must be advisedly checked before lifting lamp-postal service, bank check if lamp head or solar console has whatever deviation, and make moderate aligning.

(2) Slowly lift lamp-post, avoid steel wire rope of crane to scratch solar panel.

(iii) Slowly put down lamp-mail and rotate the lamp-post to adjust its orientation.

(iv) After the ring flange existence into foundation, gradually sheathe flat gasket, spring pad and nut, then use wrench to tighten nut and fasten lamp-post.

(5) Remove the lifting rope, and cheque if having whatever incline.

4) The Installation of Bombardment and Controller.
(i) Put battery within battery box, and use thin wire to thread battery cable to the surface of foundation.

(2) Connect the cable of battery with controller co-ordinate to technical requirement. Connect with battery at outset, then connect with loads, subsequently so connect with solar panel. Delight notice each wiring final when connecting the wires, positive and negative pole can't exist reverse connexion, otherwise it would harm controller.

(3) Debug to check if the solar street light normally work, gear up controller mode, allow the solar lamp work, to check if having any trouble, after setting lighting time, sealing the cover of lamp-mail.

(4) The wiring connection diagram of smart controller.

iii. The Aligning of Solar Panel and The Second Embedded.
1) Please bank check the installation effect of whole solar street lights after completing the installation, please conform the one which has any incline. Ultimately to keep all of solar street lights be uniform.

ii) Cheque the orientation of solar panel, need adjust the orientation of solar console toward Due S in China. (Orientation is unlike in unlike Countries).

3) Check whether the lamp-arm has any incline, lamp caput is moderation. Need adjust them if having any unsuitability.

four) Please procedure the 2d embedded for the foundation of lamp-post after checking everything beingness no problem. Use cement to chip the foundation to be a minor foursquare block, to make the solar street light exist more fastness and reliability.

To a higher place is the introduction of installation procedure for solar street calorie-free, it is easy to install and no need pave complicated cables, cleaning free energy and no need pay electric fee. It is developing and technical tendency.

Bingsolar Power, eighth, Apr, 2022